14 Top Aem Electronics

 

AEM Electronics 30-5501

AEM Electronics 30-5501

AEM Electronics 30-5501 - 30-5501. Supply current 5 vdc. Knob set screw 1/16″ allen. Output see table below. Elec termination overmold weatherproof body with 12″ leads, 1 red (supply voltage 5vdc +/- 5), 1 black (ground), 1 white (output).

 

AEM Electronics 30-3829 MEFI PNP Jumper kit for Infinity series 3 to MEFI 4

AEM Electronics 30-3829 MEFI PNP Jumper kit for Infinity series 3 to MEFI 4

AEM Electronics 30-3829 MEFI PNP Jumper kit for Infinity series 3 to MEFI 4 - Aem mefi pnp jumper kit for infinity series 3 ecu.

 

AEM Electronics 35-4500-20 20 Foot WaterMethanol Injection Nylon Hose 14 inch

AEM Electronics 35-4500-20 20 Foot Water/Methanol Injection Nylon Hose 1/4 inch

AEM Electronics 35-4500-20 20 Foot Water/Methanol Injection Nylon Hose 1/4 inch - Accurate and affordable. High-quality sealed sensor housings. Includes bosch lsu 42 connector, 7 x wire seals & 7 x contacts. Note product image may not be vehicle specific. Mating connector and pins included (most sensors).

 

AEM Electronics 30-3003 WaterMethanol Injection Inline Filter

AEM Electronics 30-3003 Water/Methanol Injection Inline Filter

AEM Electronics 30-3003 Water/Methanol Injection Inline Filter - Micronic mesh screen out-performs sintered filters in both filtering and serviceability. Why you want oneif you are using a water/methanol injection system it may greatly increase pump life to use a water/methanol filter. The aem water/methanol injection filter is an in-line filter that uses a micronic mesh screen to filter particulates as small as 40 microns. This allows a cleaner flow of water/methanol to be passed into the engine not only protecting the internals of the engine itself but also the working parts of the water/methanol pump too. Large filtering area assure long service life and does not significantly reduce flow. Run the aem water/methanol injection filter in-line before the pump to protect both pump and engine. Stainless steel mesh strainer, aems custom mesh strainer filters down to 40 microns, much smaller than similar filters. Polypropylene housing, rugged material that is compatible with high concentrations of methanol. The aem water/methanol injection filter uses fittings for use with 1/4″ od nylon tubing so it fits most water/methanol injection kits on the market todaysimple to install takes less than a minute. Completely serviceable assembly, can be disassembled cleaned and reused for a long service life. Fits virtually every water/methanol system on the market. The aem water/methanol injection filter prevents foreign particles as small as 40 microns from clogging or damaging pumps injection nozzles check valves or flow sensors. Note for optimum results all water / methanol injection systems and gauges should be run with an inline filter.

 

AEM Electronics 35-4005 Mild Steel O2 Sensor Bung

AEM Electronics 35-4005 Mild Steel O2 Sensor Bung

AEM Electronics 35-4005 Mild Steel O2 Sensor Bung - High-quality sealed sensor housings. Mating connector and pins included (most sensors). Accurate and affordable. Note product image may not be vehicle specific. Includes bosch lsu 42 connector, 7 x wire seals & 7 x contacts.

 

AEM Electronics 25-109BK High Volume Fuel Rail

AEM Electronics 25-109BK High Volume Fuel Rail

AEM Electronics 25-109BK High Volume Fuel Rail - 1996-2000 > honda > civic > 16l l4 1590cc d16y8 > ex. 1996-1997 > honda > civic > 16l l4 1590cc d16y8 > del sol si. 1996-2000 > honda > civic > 16l l4 1590cc d16y7 > cx dx lx. 1996-1997 > honda > civic > 16l l4 1590cc d16y7 > del sol s. Note product image may not be vehicle specific.

 

AEM Electronics 30-2131-30 2 BAR  30 PSIA MAP SENSOR KIT

AEM Electronics 30-2131-30 2 BAR / 30 PSIA MAP SENSOR KIT

AEM Electronics 30-2131-30 2 BAR / 30 PSIA MAP SENSOR KIT - Sensor performance specifications accuracy +/- 3% full scale over -40c to 105c includes repeatability hysteresis and linearity operating temp -20c to 105c / -4f to 221f burst pressure 60psi response time < 1ms wetted materials 304l & 316l stainless steel vibration 100 to 2000hz 20g sinusoidal 3 axes weight. All aem sensors include a flying lead with a weather-tight seal and 12 inch insulated wires that are color coded in black green and red this is important since the correct connector will give you the most accurate voltage possible.

 

AEM Electronics 30-5503 Digital Display CD-7L logging CAN race dash with VDM 30-2203 include

AEM Electronics 30-5503 Digital Display CD-7L logging CAN race dash with VDM (30-2203) include

AEM Electronics 30-5503 Digital Display CD-7L logging CAN race dash with VDM (30-2203) include -  full color 7” screen with 800×480 resolution 1000cd/m2 brightness and anti-glare filter for readability in all conditions including direct sunlight ip66 water resistance allows for operation in boats and motorcycles without worry accepts channels from two separate user programmable can bus connections – works with aemnet enabled devices and 3rd party devices side by side available with or without 200mb internal logging (up to 100hz/channel) seven programmable pages including four main pages, alarm, on-change and start-up pages dedicated alarm page quickly identifies problems (user defined) free dashdesign graphics editor software seven led rpm/shift light indicators on top of the housing (programmable and dimmable) two programmable leds above toggle buttons on sides of housing odometer function over 200 supplied fully programmable warning icons, and you can add your own‘headlight-in’ connection dims the dash and leds during night operation two extra switch inputs included for displaying user-triggered events (blinkers, high beams etc. They are designed to accept channels from can bus connections and do not include analog inputs. The cd-7/cd-7l color digital displays feature a super bright, high contrast, sunlight readable display and include an integrated glare diffuser and shade hood so that they are readable in even the brightest daylight conditions. Two can bus channels are included so that it can receive and collect data from aemnet enabled devices such as the infinity ecu, series 2 ems or ems-4, and 3rd party devices including pdm’s, can sensor modules and programmable engine management systems. ) User supplied graphics can be changed based on channel values (up to the full screen size) convert can bus channel values to user-defined text.

 

AEM Electronics 30-3305 V2 Multi Input Controller Kit

AEM Electronics 30-3305 V2 Multi Input Controller Kit

AEM Electronics 30-3305 V2 Multi Input Controller Kit - The multi-input controller works with an external 0-5v voltage-based external map sensor a frequency based input for injector duty cycle (idc) frequency-based mass airflow (maf) or a 0-5v voltage-based maf. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. Aem multi-input water/methanol injection controller and wiring harnessaems multi-input water/methanol injection controller features a multiple input design that enables users to install it on both high compression naturally aspirated vehicles (na) via the maf/idc settings and ultra-high boost vehicles (above 35 psi) using an external map sensor. The multi-input controller has an easy-to-remove plug covering the programming dipswitches and a programming legend on the back for the 0-5v and frequency based settings. A plug is integrated into the controller housing for mating to the redesigned wiring harnesss positive-lock connector. This means that the flow delivery better matches an engines need for water/methanol injection which further optimizes charge air cooling and detonation control on gasoline engines or egt reduction on turbo diesels. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. Aems engineers spent extensive time developing the controllers flow control strategy for a more linear flow output delivery. Aems water/methanol injection wiring harness for the multi-input controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. The controller design features large turn-resistant knobs and larger numbering to easily set accurate start and full activation points with covered status led and test buttons for added splash resistance. Legal in california onl. The controller housing features an easy to access integrated fuse and molded mounting tabs.

 

AEM Electronics 30-2130-50 50 PSIa35 Bar Stainless Steel Sensor Kit - 18 inch NPT Male Thread

AEM Electronics 30-2130-50 50 PSIa/3.5 Bar Stainless Steel Sensor Kit – 1/8 inch NPT Male Thread

AEM Electronics 30-2130-50 50 PSIa/3.5 Bar Stainless Steel Sensor Kit – 1/8 inch NPT Male Thread - Sensor performance specifications accuracy +/- 1% full scale over -40c to 105c includes repeatability hysteresis and linearity operating temp -40c to 105c / -40f to 221fburst pressure 500psi response time < 1ms wetted materials 304l & 316l stainless steel vibration 100 to 2000hz 20g sinusoidal 3 axesweight. All aem sensors include a flying lead with a weather-tight seal and 12 inch insulated wires that are color coded in black green and red this is important since the correct connector will give you the most accurate voltage possible.

 

AEM Electronics 30-8444 Universal Weather Resistant 52mm Gauge Boot

AEM Electronics 30-8444 Universal Weather Resistant 52mm Gauge Boot

AEM Electronics 30-8444 Universal Weather Resistant 52mm Gauge Boot - Our gauge boot protects your gauges to maximize performance and longevity. Dust and weather proof when installed correctly, however it is not water proofif you have a race car off road truck motorcycle ruckus snowmobile atv or other vehicle that is in a muddy/dusty/snowy/weather exposed environment you need to protect the back of your gauges. Aem’s universal gauge boot acts like a wet suit or shower cap for any 52mm gauge. It is made of silicone and is designed to stretch onto the back virtually any 52mm gauge and keeps dust and water out of the back of the gauge. Even under the dash of a race car the back of the gauge is exposed to dirt and dust which can deteriorate the electronics in your gauge.

 

AEM Electronics 30-2012 WATERCOOLANT TEMPERATURE SENSOR KIT 18 inch NPT

AEM Electronics 30-2012 WATER/COOLANT TEMPERATURE SENSOR KIT (1/8 inch NPT)

AEM Electronics 30-2012 WATER/COOLANT TEMPERATURE SENSOR KIT (1/8 inch NPT) - 1/8″-27 ptf. 2%+ti]. The ratio at a specified ambient temperature of the change in the power dissipation of the sensor to the resultant temperature change of the thermistor. The time required for the sensor to achieve 63. Termination connector. Sensor performance specificationsaccuracy < 2c / 3. Includes water / coolant / oil temp sensor plug pins & pin lock. Includes mating connector pins & pin lock. Test medium silicone oil. 6foperating temp -40c to 200c / -40f to 392fresistive range () see tabledissipation constant 12 mw/c. Sensor body material brassthread 1/8"-27 ptfhex size 1/2"installation torque 13. Test medium silicone oil. 2% of its steady state value when subjected to a step change in ambient temperature [tc=(tf-ti)63. Thermal time constant 10 sec. Water / coolant / oil temp sensor kit. 2gsupply current 5vdcelec. 5nm / 10 ft-lbsweight 12.

 

AEM Electronics 30-3304 V2 Standard Controller Kit

AEM Electronics 30-3304 V2 Standard Controller Kit

AEM Electronics 30-3304 V2 Standard Controller Kit - Legal in california only for racing vehicles which may never be used upon a highway. An additional wire is included for adding an optional on/off solenoid to stop fluid flow when the system is inactive. The controller design features large turn-resistant knobs and larger numbering to easily set accurate start and full activation points with covered status led and test buttons for added splash resistance. It has an on-board manifold absolute pressure (map) sensor with a molded-in barbed nipple for a boost hose pickup. All aem water/methanol injection systems and components (pump lines fittings filter flow sensor tank and nozzles) are 100% chemically. Aems water/methanol injection wiring harness for the boost dependent 35 psi controller is terminated with a positive-lock connector on one end and has color-coded wires to ease installation. Aem 35 psi boost dependent water/methanol injection controller and wiring harnessaems boost dependent water/methanol injection controller is ideal for vehicles running up to 35 psi of boost. Aems engineers spent extensive time developing the controllers flow control strategy for a more linear flow output delivery. This means that the flow delivery better matches an engines need for water/methanol injection which further optimizes charge air cooling and detonation control on gasoline engines or egt reduction on turbo diesels. A plug is integrated into the controller housing for mating to the redesigned wiring harnesss positive-lock connector. The boost dependent controller housing includes a wiring legend on the back easy to access integrated fuse and molded mounting tabs. Both the power and ground wires for the pump are included in the harness which simplifies the wiring process and eliminates any chance of the pump accidentally activating from a short in the system. Important safety notice regarding methanolaem strongly recommends that users never exceed a 50% methanol concentration when using any aem water methanol system or component.

 

AEM Electronics 25-304BK Adjustable Fuel Pressure Regulator Offset Flange with 90 Degree Return Line Fitting 1997-1997 Acura CL

AEM Electronics 25-304BK Adjustable Fuel Pressure Regulator (Offset Flange with 90 Degree Return Line Fitting) 1997-1997 Acura CL

AEM Electronics 25-304BK Adjustable Fuel Pressure Regulator (Offset Flange with 90 Degree Return Line Fitting) 1997-1997 Acura CL - Fuel rail or aem high volume fuel railmanufactured and assembled in the usa. 2l 96-97aems honda/acura adjustable fuel pressure regulators are capable of supporting enough fuel flow for engines up to 1000 horsepower. Adjustable from 20 psi to maximum fuel pump capacityinterchangeable discharge ports match regulator output to output of any fuel pumppatent # 6,298,828cnc-machined from 6061-t6 billet aluminumno additional parts required for installationmounts directly to o. Our patented interchangeable discharge ports enable the regulators output to match the output of any fuel pump. Aem includes a custom barb fitting to accommodate the factory fuel hose and the base of each regulator is tapped to accept a -6 an or 9/16″x18 fittings. Aem high volume adj fuel pressure regulator acura cl 2. Legal in california only for racing vehicles which may never be used upon a highway. E.